-
Donation Goals
Hackintosh Monthly Donation - AprilHackintosh Shop was made possible by using your donations & displaying ads which covers the running cost.
Thanks
20%
-
-
-->
12 hours ago, Hackintosher said:You are applying too many boot-flags also you are booting from Chameleon, Keep pressing Number 6 while it boots, You will be directed into Clover, Boot with Clover.
thank you, the boot flags where only for 1 or 2 tries , the only boot flag i am using every time is the npci=0x3000 untill i get it running and can get something more permanent in place.
OMG thank you about the number "6" thing i had no idea
managed to boot it into clover witch is HEAPS better. i will have a go at patching the usb problem so i can get it to install. any advice id appreciate.
so after a few hrs fiddling around i don't think i am any closer. i refollowed the guides here with no luck,
picture of current issue https://drive.google.com/file/d/1cB2giBeStwoAo2kI-CRKnpxPQ_U-YSXa/view?usp=sharing
i also noticed i probably didn't give enough info in the first post so i'll add some here.
Motherboard
Manufacturer Gigabyte Technology Co. Ltd.
Model GA-MA770T-UD3P (Socket M2)
Chipset Vendor AMD
Chipset Model 770
Chipset Revision 00
Southbridge Vendor AMD
Southbridge Model SB700
Southbridge Revision 00
Graphics
Monitor
Name BenQ M2700HD on AMD Radeon HD 7700 Series
Current Resolution 1920x1080 pixels
Work Resolution 1920x1040 pixels
State Enabled, Primary
Monitor Width 1920
Monitor Height 1080
Monitor BPP 32 bits per pixel
Monitor Frequency 60 Hz
Device \\.\DISPLAY1\Monitor0
ATI AMD Radeon HD 7700 Series
Manufacturer ATI
Model AMD Radeon HD 7700 Series
Device ID 1002-683F
Subvendor Sapphire/PCPartner (174B)
Current Performance Level Level 0
Current GPU Clock 300 MHz
Current Memory Clock 400 MHz
Current Shader Clock 400 MHz
Voltage 0.950 V
GPU Clock 800.0 MHz
Temperature 35 °C
Core Voltage 1.100 V
Driver version 26.20.12028.2
BIOS Version 113-E228DA32G-X004
Memory Type DDR3
Memory 2048 MB
Bandwidth 25.6 GB/s
CPU
AMD Phenom II X4 965
Cores 4
Threads 4
Name AMD Phenom II X4 965
Code Name Deneb
Package Socket AM3 (938)
Technology 45nm
Specification AMD Phenom II X4 965 Processor
Family F
Extended Family 10
Model 4
Extended Model 4
Stepping 3
Revision RB-C3
Instructions MMX (+), 3DNow! (+), SSE, SSE2, SSE3, SSE4A, AMD 64, NX, VMX
Virtualization Supported, Enabled
Hyperthreading Not supported
and here is a copy of my current EFI folder https://drive.google.com/file/d/1GOWMjT6zhEqxM8tQyj5sJOa-Ydt1egvs/view?usp=sharing
thanks for the help.
Edited by Groovyaxis2
Hackintosh Shop 312
I think you are Installing the lastest FakeSMC from Customize section.
If you could replace the fakeSMC in the destination volume it might be able to boot.
On 12/31/2020 at 6:20 AM, Hackintosher said:I think you are Installing the lastest FakeSMC from Customize section.
If you could replace the fakeSMC in the destination volume it might be able to boot.
thanks for the info, i'll check it out. though i'd like to check when you say the "destination volume" do you mean on the usb boot device?
the hdd volume i have set for sierra is actually empty at the moment
On 12/30/2020 at 1:00 PM, Groovyaxis2 said:managed to boot it into clover witch is HEAPS better. i will have a go at patching the usb problem so i can get it to install. any advice id appreciate.
I have acer nitro 5 model number is AN515-42
Processor AMD Ryzen 5 2500U with Radeon Vega Mobile Gfx 2.00 GHz
Installed RAM 16.0 GB (14.9 GB usable)
System type 64-bit operating system, x64-based processor
Pen and touch No pen or touch input is available for this display
Gpu : Rx 560x
I have tried almost all version but getting error while Installing .
here is the link of the photo ...It always get stuck here
https://drive.google.com/file/d/1jc9Nz9bglXpy6xkuNDTeb8it_P9Nz1hJ/view?usp=sharing
Plz help me out. Thanks
You are applying too many boot-flags also you are booting from Chameleon, Keep pressing Number 6 while it boots, You will be directed into Clover, Boot with Clover.
Share this post
Link to post
Share on other sites